1. Prepare substructure for screwing module into drywall ceiling.
2. Feed cable through opening in plaster module.
3. Carefully screw plaster module into prepared opening.
4. Adding fabric tape, fill the joints. Make sure to plaster the joints only and not the entire module.
Prime and paint the plaster module with the ceiling paint. Plaster modules are not suitable for coarse plaster!
CAUTION: Please check with your plasterer if you want to use coarse, loam, or acoustic plaster.
Plaster modules are brittle and may break easily.
Reserve enough space for cooling element. Observe minimum installation depth for module and luminaire. If a luminaire with cooling element is used, do not cover it with insulation material, steam brake, fleece or film!
1. Drill a Ø68mm hole.
2. Run cable through opening of the filler inset. insert the module into the prepared cutout.
3. Insert the module into the prepared cutout and screw it into the ceiling from below. Make sure that the filler inset rests flat and clean on the plasterboard and is firmly pulled down by the screws.
4. Adjust filler ring to desired filling thickness (0-15mm). Make sure plaster claws do not stick out toward the front. Claws must be completely covered by plaster.
5. Fasten supply line to protective cover and use cover to close opening.
6. Plaster ceiling in thickness of your choice.
7. Carefully sand red protective cover until it is entirely visible.
CAUTION: Do not abrade protective cover or the plaster claws will be exposed.
8. After sanding, remove protective cover and pull cable to the front. Imprecisions have to be reworked by hand.
9. Prime and paint module and filler ring with ceiling paint.
Please check with your plasterer if you want to use coarse, loam, or acoustic plaster.
Reserve enough space for cooling element. Observe minimum installation depth for module and luminaire. See the installation instructions for the respective luminaire.
1. Prepare substructure for screwing installation module into drywall ceiling. Use screwdriver to clear openings for empty conduits in the lid and clean them. Press empty conduits
into the openings until they are fastened (about two or three corrugations).
2. Screw drywall capsule into intended opening.
3. Use filler ring to adjust filling edge to desired plaster thickness. Make sure plaster claws do not stick out to the front. Claws must be completely covered by plaster.
4. Fasten supply line to protective cover and use it to close opening. Make sure plaster claws have a solid grip in the plaster.
5. Plaster ceiling in thickness of your choice.
6. Carefully sand protective cover until it is entirely visible.
CAUTION: Do not abrade protective cover or the plaster claws will be exposed.
After sanding, remove protective cover and pull cable to the front. lmprecisions have tobe reworked by hand.
Prime and paint module and filler ring with ceiling paint.
CAUTION: Please check with your plasterer if you want to use coarse, loam, or acoustic plaster.
1. Drill a 32mm hole.
2. Drywall mounting ring into opening from below, add cable holder and fasten filler ring with screw nut from above.
CAUTION: Make sure to place plaster claws flat on drywall. Plaster claws must not protrude into space below.
3. Secure cable to cable holder with cable tie.
4. Fasten supply line to protective cover and use the cover to close opening. Make sure plaster claws do not stick out to the front. Claws must be completely covered with filler.
5. Plaster ceiling.
6. Carefully sand protective conver until it is entirely visible.
CAUTION: Do not abrade protective cover or the plaster claws will be exposed.
After sanding, remove protective cover and pull cable to the front. Imprecisions have to be reworked by hand.
Prime and paint the filler ring with the ceiling paint. Module is not suitable for coarse plaster!
CAUTION: Please check with your plasterer if you want to use coarse, loam, or acoustic plaster. Alternatively Spackling insert 68-28 (Item No. 208862) therefore may be more suitable.
Reserve enough space for cooling element. Observe minimum installation depth for module and luminaire. If a luminaire with cooling element is used, do not cover it with insulation material, steam brake, fleece or film!
.jpg?size=628x440&v=kbgqpX%2BiSoWI23TBZdb6sIRfN6g%3D)
.jpg?size=53x37&v=kbgqpX%2BiSoWI23TBZdb6sIRfN6g%3D)
.jpg?size=628x440&v=saFGQCX68w%2F1CF47hd%2FJUMunVz0%3D)
.jpg?size=628x440&v=1F76Cwg7UYNuMvBQuRmAH0dIrCE%3D)
.jpg?size=53x37&v=saFGQCX68w%2F1CF47hd%2FJUMunVz0%3D)
.jpg?size=53x37&v=1F76Cwg7UYNuMvBQuRmAH0dIrCE%3D)
